Just How to Install a Bathtub
Just How to Install a Bathtub
Blog Article
The content below in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is definitely captivating. You should check it out.
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old tub is readily easily accessible, the task can relocate quickly; if you have to open a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices and material list must make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. When the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before proceeding to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the tap and the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed placement. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reads level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water and also examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at least once as this will resolve it right into its last position.
Preparing for the Installment
First of all, the supporting structure supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and also the tiling, causing difficulties with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealer can fracture fairly very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that report about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different web page. Do you know about someone else who is fascinated about the subject? Please feel free to share it. I praise you for your time. Visit us again soon.
Book Now! Report this page